 |
記事内容:[|]
大変申し訳ありません。jwc.batのプロパティのプログラムのタグ内でBATファイルに
「DOSIME」の記述があったので消しました。しかし、まだエラーが出ます。
それぞれのファイルの中身について明示します。お手数をかけますがお願いしま
す。
【C:\jwc\jwc.bat】の中身
c:\JWC\JW_CADV /A /R5,5 /P3 /E1 /B300 /H1,250 /O /L8 /H2 /M4 /コ /F&128
call jp.bat
CD\
【c:windows\system32\AUTOEXEC.NT】の中身
@echo off
REM AUTOEXEC.BAT is not used to initialize the MS-DOS environment.
REM AUTOEXEC.NT is used to initialize the MS-DOS environment unless a
REM different startup file is specified in an application's PIF.
REM Install CD ROM extensions
lh %SystemRoot%\system32\mscdexnt.exe
REM Install network redirector (load before dosx.exe)
lh %SystemRoot%\system32\redir
REM Install DPMI support
lh %SystemRoot%\system32\dosx
REM
REM *************************************************
REM ** 以下の行は、元の Microsoft Windows ME 設定から
REM ** 移行されました。
REM *************************************************
REM
SET windir=C:\WINDOWS
SET winbootdir=C:\WINDOWS
SET COMSPEC=C:\WINDOWS\COMMAND.COM
SET PATH=C:\WINDOWS;C:\WINDOWS\COMMAND
SET PROMPT=$p$g
SET TEMP=C:\WINDOWS\TEMP
SET TMP=C:\WINDOWS\TEMP
REM
REM *************************************************
REM ** 以下の行は、２００３年４月２８日追加した。
REM **
REM *************************************************
REM
comspec=%SystemRoot%\system32\command.com
【c:windows\system32\CONFIG.NT】の中身
REM Windows MS-DOS Startup File
REM
REM CONFIG.SYS vs CONFIG.NT
REM CONFIG.SYS is not used to initialize the MS-DOS environment.
REM CONFIG.NT is used to initialize the MS-DOS environment unless a
REM different startup file is specified in an application's PIF.
REM
REM ECHOCONFIG
REM By default, no information is displayed when the MS-DOS environment
REM is initialized. To display CONFIG.NT/AUTOEXEC.NT information, add
REM the command echoconfig to CONFIG.NT or other startup file.
REM
REM NTCMDPROMPT
REM When you return to the command prompt from a TSR or while running an
REM MS-DOS-based application, Windows runs COMMAND.COM. This allows the
REM TSR to remain active. To run CMD.EXE, the Windows command prompt,
REM rather than COMMAND.COM, add the command ntcmdprompt to CONFIG.NT or
REM other startup file.
REM
REM DOSONLY
REM By default, you can start any type of application when running
REM COMMAND.COM. If you start an application other than an MS-DOS-based
REM application, any running TSR may be disrupted. To ensure that only
REM MS-DOS-based applications can be started, add the command dosonly to
REM CONFIG.NT or other startup file.
REM
REM EMM
REM You can use EMM command line to configure EMM(Expanded Memory Manager).
REM The syntax is:
REM
REM EMM = [A=AltRegSets] [B=BaseSegment] [RAM]
REM
REM AltRegSets
REM specifies the total Alternative Mapping Register Sets you
REM want the system to support. 1 <= AltRegSets <= 255. The
REM default value is 8.
REM BaseSegment
REM specifies the starting segment address in the Dos conventional
REM memory you want the system to allocate for EMM page frames.
REM The value must be given in Hexdecimal.
REM 0x1000 <= BaseSegment <= 0x4000. The value is rounded down to
REM 16KB boundary. The default value is 0x4000
REM RAM
REM specifies that the system should only allocate 64Kb address
REM space from the Upper Memory Block(UMB) area for EMM page frames
REM and leave the rests(if available) to be used by DOS to support
REM loadhigh and devicehigh commands. The system, by default, would
REM allocate all possible and available UMB for page frames.
REM
REM The EMM size is determined by pif file(either the one associated
REM with your application or _default.pif). If the size from PIF file
REM is zero, EMM will be disabled and the EMM line will be ignored.
REM
EMM=RAM
dos=high, umb
device=%SystemRoot%\system32\himem.sys
devicehigh=%SystemRoot%\system32\ntfont.sys
devicehigh=%SystemRoot%\system32\font_win.sys
devicehigh=%SystemRoot%\system32\$disp.sys /hs=%HardwareScroll%
devicehigh=%SystemRoot%\system32\disp_win.sys
devicehigh=%SystemRoot%\system32\kkcfunc.sys
files=40
device=%SystemRoot%\system32\MSIMEK.SYS /A1
devicehigh=%SystemRoot%\system32\MSIMEI.SYS /D*%SystemRoot%\system32
\MSIMER.DIC /D%SystemRoot%\system32\MSIME.DIC /C1 /N /A1
REM *************************************************
REM ** 以下の行は、２００３年４月２８日追加した。
REM **
REM *************************************************
devicehigh=%SystemRoot%\system32\ansi.sys /X
|
